Detnov – Special Detectors

Detnov
Detnov
- Special Detectors
Beam Smoke Detector
  • EN 54-12:2015 approved
  • Very low consumption
  • Self-alignment
  • Programmable sensitivity
  • Alarm and fault relay outputs
  • Automatic dirt compensation
  • Distances over 7 meters and up to 70 meters, expandable up to 140 or 160 meters
  • Optional anti-condensation kit
  • Environment: IP65, Temp -10 to +55°C, Humidity 10% to 95% without condensation
  • Applications: large rooms or large areas such as industrial warehouses, warehouses, shopping malls, museums, etc.
FIREBEAM XTRA is ideal for the protection of large areas where the use of traditional detection technologies is difcult and costly to install.
Duct Smoke Detector
  • One-pipe air sampling system
  • Venturi pipe and housing are specially designed for optimum airflow through the smoke detector
  • Conventional or analogue addressable detectors
  • Test hole on cover
  • Airflow speeds: 0.2 m/s to 20 m/s
  • Sampling pipe length 600mm, Extension pipe 1,5m
  • Environment: IP54, Temp -20 to +50°C
  • Material: ABS plastic
  • Dimension: 180 x 235 x 183 mm
Duct Smoke Detector has been developed to detect smoke in ventilation ducts
IR2, IR3, UV/IR2 Flame Detectors
  • Designed, manufactured and certifed according to EN54-10
  • 90° degree detection cone and detection distance up to 45 meters
  • Selectable outputs: Relay output via dry contact or 4-20 mA output
  • Programmable sensitivity Includes filters and microprocessor analysis to eliminate false alarm
  • Power supply 14 - 30 V @28 mA
  • IR2 flame detector:
    • Spectral response in the infrared: 0.75 to 2.7 µm
    • Range: Class 1 – flame size 0.1m² n-heptane at 25m; Class 3 – flame size 0.1m² n-heptane at 12m
    • Approval: CPR, LPCB, AFNOR, SIL2
  • IR3 flame detector:
    • Spectral response in the infrared: 0.75 to 2.7 µm
    • Range: Class 1 – flame size 0.1m² n-heptane at 25m; Class 3 – flame size 0.1m² n-heptane at 12m
    • Approval: FM Approval, CPR, LPCB, VDS, SIL2
  • UV/IR2 flame detector:
    • Spectral response: 1 to 2.7 µm in the infrared, 185 to 260nm in the ultraviolet
    • Range: Class 1 – flame size 0.1m² n-heptane at 25m; Class 3 – flame size 0.1m² n-heptane at 12m
    • Approval: FM Approval, CPR, LPCB, VDS, SIL2
IR2
– IR², IR3, UV/IR2 flame detectors
– Certifed EN54-10
IR2
– IR², IR3 flame detectors
– Rated ATEX Ex II 1 G, Cenelec / IEC Ga Ex d IIC T4, for zones 0, 1 or 2
IR2_EX
– IR², IR3, UV/IR2 flame detectors
– Intrinsically safe applications with flameproof IP66 cover
– Rated ATEX II 2 G D, Cenelec / IEC Ex d IIC T4 Gb and Ex IIIC T135ºC Db IP66 A21, for zones 1, 2, 21 or 22.
Applications: suitable for heavy industries, oil & gas…
  • Refineries
  • Generators
  • Compressor Stations
  • High Voltage Equipment
  • Power Plants
  • Fuel Loading Racks
  • Chemical Plants
  • Industrial heating and drying systems, and furnaces
  • Printing, spray booths
  • Tunnels
  • Nuclear Power Sites
  • Storage Tanks
  • Engine Rooms
  • Pharmaceutical Production
  • Military Applications
  • Marine Industry
  • Aircraft Hangars
  • Petrochemical Offshore/Onshore
  • LNG/LPG Production
Gas Detectors
  • Autonomous operation or via addressable Detnov system
  • FIGARO semiconductor sensors
  • Easy installation surface or DIN rail
  • Detection of natural gas, and LPG (methane, butane and propane)
  • The alarm levels are 5000 ppm for the natural gas detectors and 2000 ppm for the LPG detectors.
  • Alarm relay and fault relay 1A@30VDC
  • 3 status LEDs
  • Test button
  • Wiring connection: 2 x 1,5 mm² twisted and shielded cable
  • Environment: IP32D, Temp -10 to +400C, Humidity 95% without condensation
  • Approvals: EN 50194-1
Detectors for natural gas and liquefied petroleum gas (LPG): butane and propane